Hydraulic elevators are elevators which are powered by a piston that travels inside a cylinder. An electric motor pumps hydraulic oil into the cylinder to move the piston. The piston smoothly lifts the elevator cab. Electrical valves control the release of the oil for a gentle descent.
Hydraulic elevators are used extensively in buildings up to five or six stories high. Sometimes, but rarely, up to 8 stories high. These elevators, which can operate at speeds up to 61 meters (200 ft) per minute, do not use the large overhead hoisting machinery the way geared and gearless traction systems do.
All modern hydraulic pumps are either equipped with a Solid-State Contactor or a mechanical Y-Delta starter. Solid-State Contactor statrers are better for the motor and the building's power supply, as the windings last longer and there are no voltage drops across the line of the building's power supply. Y-Delta starters use two contactors to start the motor on a reduced speed, then kick on full speed. Old hydraulic elevators just started up abruptly, sending mains power at full blast right into the motor. This puts a lot of strain on the motor which, in turn, makes it burn out faster than motors on Y-Delta or Solid-State Contactor starters.
There are three types of hydraulic elevator; holed hydraulic, holeless hydraulic and roped hydraulic.
With holed hydraulic systems (also known as direct acting lift), the elevator car is mounted on a piston that travels inside a cylinder. The cylinder extends into the ground to a depth equal to the height the elevator will rise. As hydraulic fluid is pumped into the cylinder through a valve, the car rises. As the fluid returns to the reservoir, the car descends. This system is often called Inground hydraulic.
Holeless hydraulic elevators were invented in the late 1970's or a little earlier. Holeless hydraulic elevators of pistons mounted inside the hoistway to raise and lower the car. This is especially a solution for buildings built in bedrock, a high water table or unstable soil conditions locations that can make digging the hole required for a conventional hydraulic elevator impractical. Holeless hydraulic systems use a direct-acting piston to raise the car.
Roped hydraulic elevator (also known as indirect acting lift) extends the rise of the holeless elevator to 18 meters (60 ft), without the need for a belowground cylinder. As the higher power of the hydraulic cylinder and the power unit, The 1:2 ratio (power from the hydraulic power unit : elevator actual moving distance) can be provided. Roped hydraulic elevator systems have the piston attached to a sheave which has a rope passing through it. One end is attached to the car while the other is secured at the bottom of the hoistway. Also, roped hydraulic systems require a governor because the rope is holding the car up, and there is a risk of the car freefalling when the rope breaks.
Machine room less hydraulic
- Further information: Machine room less elevator
This hydraulic elevator does not require a fixed room to house the hydraulic machinery, instead, the machinery itself is usually installed on the elevator pit and the controller is installed behind a locked cabinet on the wall near the elevator. The benefit of machine room less hydraulic elevator is that it saves construction time and cost. Examples of machine room less hydraulic elevator is Otis HydroFit and thyssenkrupp Endura MRL.
Benefits of Hydraulic Elevators
- No need for reinforcement. The cylinder that lifts the elevator cab is supported by the ground underneath (for holed hydraulic only).
- Are usually cheaper than traction units.
- If the line breaks, the elevator will fall no faster than oil can escape.
Detriments of Hydraulic Elevators
Older hydraulic elevators may have a risk of leaking hydraulic oil into an aquifer and causing potential environmental contamination. This has led to the introduction of PVC liners (casings) around hydraulic cylinders which can be monitored for integrity. Additionally, older hydraulic elevator systems usually have a motor outside of the tank and cause noise when the motor is running (this layout is no longer used in the hydraulic elevators installed in mid-1990's or later, when the submersible hydraulic power unit was introduced. The motor is placed inside the tank and the motor sound is isolated by the oil in the tank).
In 2007, Kone announced that the company would stop manufacturing and producing hydraulic elevators due to environmental concern, therefore replacing them with the eco-friendly MonoSpace and EcoSpace elevators. This makes Kone the first elevator company to only produce traction elevators. Also, some other elevator manufacturers have stopped producing hydraulic elevators due to the same reason.
Notable hydraulic elevator models
- Oildraulic (1937 - 2012) - notable hydraulic elevator system invented by Automobile Rotary Lift Co., normally used on Dover and ThyssenKrupp elevators in the United States and Canada.
- Schindler 300A (1993 - 2004)
- Schindler 321A (1997 - 2001)
- Schindler 330A (2001 - present)
- Kone HH and MX Series (Discontinued in 2007)
- Otis 211 (1980 - 2013) - common hydraulic controller used on Otis elevators.
- Otis HydroFit (2011 - present) - Otis's new hydraulic system. Also comes with MRL option.
- thyssenkrupp Endura (2012 - present) - successor to the Oildraulic.
- thyssenkrupp Endura MRL (2014 - Present) - successor to the Oildraulic; MRL version of Endura.
- Mitsubishi Hydraulic Elevator
- EasyGo-h - machine room less hydraulic elevator produced by Daldoss.
- EasyLife - compact hydraulic elevator produced by Daldoss (now discontinued)
- 3G 3035 / 3037 - hydraulic elevator for heavy loads produced by Orona.
Notable hydraulic component suppliers
Notes and references
- Hydraulic lifts (hkelev.com)
- Toshiba Elevator and Building Systems Corporation - Elevator Basics: Hydraulic Elevators
|Elevator drive systems|
|Traction • M.R.L. • Winding Drum • Hydraulic (Oildraulic)|
|Reference: hkelev - Elevator drive systems
Return to Homepage: Click here